Blogs

What is the best way to control the size of injection molded products and how to control it?

Jul 20, 2022 Leave a message

The appearance accuracy of injection molded products should meet strict dimensional tolerances, form tolerances and surface roughness. To carry out precision injection molding there must be many related conditions, and the most essential are the three basic factors of injection mold, injection molding process and the usual production aspects.

I. Control of mold design

1、First of all, we need to fully understand the technical requirements of users in many aspects such as mold structure, material, hardness and precision, including whether the shrinkage rate of molding plastic material is correct, whether the 3D size of the product is complete, and whether the processing analysis is reasonable.

2、To fully consider the appearance of the injection molded products such as shrinkage, flow marks, mold slope, fusion line and cracks.

3、Simplify the processing method of the mold as much as possible without hindering the function and pattern making of the injection molded products.

4、Whether the selection of parting surface is appropriate or not, careful selection should be made for mold processing, molding appearance and deburring of molded parts.

5, whether the pushing and topping method is appropriate, using the push rod, unloading plate, pushing and topping casing or other ways, whether the position of the push rod and unloading plate is appropriate.

6、Whether the use of side core extraction mechanism is appropriate, flexible and reliable action, there should be no jamming phenomenon.

7、What method of temperature control is more suitable for plastic products, which structure circulation system is used for temperature control oil, temperature control water and coolant, and whether the size, quantity and position of coolant holes are appropriate.

8、The form of sprue, the size of channel and inlet, whether the location and size of sprue are appropriate.

9、The effect of heat treatment deformation of various modules and mold cores and the appropriateness of the choice of standard parts.

10、Is the injection volume, injection pressure and clamping force of injection molding machine adequate, nozzle R, gate sleeve aperture, etc. matched appropriately.

These aspects should be analyzed and prepared comprehensively, and should be strictly controlled from the initial stage of the product.

2, the process of manufacturing control

Although in the design phase of the full consideration and arrangements, but in actual production there will be a lot of problems and difficulties, we should try to comply with the original design in production, to find the actual processing more effective, more economical and reasonable means of technology.

1, choose the economic adaptation of the machine tool equipment, for 2D and 3D machining program.

2, can also consider the appropriate tooling fixtures for production of auxiliary preparations, the reasonable use of tools, to prevent the product pieces of deformation, to prevent the product pieces of shrinkage fluctuations, to prevent the product pieces of deformation, to improve the accuracy of mold manufacturing, reduce errors, to prevent changes in mold accuracy, etc., a series of production process requirements and solutions.

3, here to mention about the British Plastics Council (BPF) of the molding parts size error generated by the causes and its proportion of the distribution of

A: mold manufacturing error about 1/3

B by the mold wear error 1/6

C by the uneven shrinkage rate of the molded parts generated by the error of about 1/3

D the error generated by the inconsistency between the scheduled shrinkage rate and the actual shrinkage rate is about 1/6

The total error = A + B + C + D, so it can be seen that the mold manufacturing tolerance should be less than 1/3 of the size tolerance of the forming part, otherwise the mold is difficult to ensure the geometric size of the forming part.

3, the usual production aspects of control

Geometry fluctuation after forming plastic parts is a common problem, and is often occurring phenomenon: 1.

1, the material temperature, mold temperature control, different grades of plastic necessary for different temperature requirements, plastic material fluidity and the use of more than two kinds of mixed materials will have different situations, plastic materials should be controlled in the best flow value range, these are usually easy to do, but the mold temperature control is more complex, different geometry, size, wall thickness ratio of different molded parts have certain requirements for the cooling system The mold temperature controls the cooling time to a large extent.

Therefore, we try to keep the mold at a low temperature to help shorten the injection cycle and improve production efficiency. If the mold temperature changes, the shrinkage rate will also change, and the mold temperature will remain stable, so that the dimensional accuracy will be stable, thus preventing the deformation of molded parts, bad gloss, cooling spots and other defects, and making the physical properties of plastic in the best condition. The molded parts are more complicated. So the mold temperature in the production process can not be changed at will, the mold temperature should be set within the recommended temperature range of the material.

2、Adjustment and control of pressure and exhaust.

Proper injection pressure, clamping force matching should be determined when commissioning the mold, the air in the mold cavity and core formed by the gap and the gas generated by the plastic must be discharged from the exhaust slot outside the mold, such as poor exhaust will appear to be underfilled, resulting in fusion marks or burns.

These three kinds of molding defects sometimes appear in the same part of the intermittent, when the thin-walled part of the molded part around the presence of thick walls, mold temperature is too low, there will be shrinkage marks, mold temperature is too high, then there will be burns, usually in the burn area and at the same time there will be fusion marks, the exhaust slot is often ignored, generally in a small state, so usually as long as no burr; the depth of the exhaust shoulder The depth of the exhaust shoulder is as deep as possible, and a larger venting groove is opened at the back of the shoulder so that the gas can be quickly discharged from the mold after passing through the shoulder.

The depth of the venting shoulder is as deep as possible, and a larger venting slot is opened at the back of the shoulder so that the gas can be quickly discharged out of the mold after passing through the shoulder, and the venting slot is opened on the top bar if there is a special need.

3, injection molding size of the supplementary plastic control

Some plastic parts due to the shape and size of the different, after demoulding with the temperature and loss of pressure changes, will occur in different cases of deformation warpage, etc., when some auxiliary tooling fixtures can be adjusted in the molding parts out of the mold in a timely and rapid remedial measures, to be naturally cooled and deformed to achieve a better correction, adjustment effect. If we ensure strict management in the whole injection molding process, the size of the injection molded parts will be very ideal control.

To sum up.

Under the joint action of these fields, different plastics (thermosetting or thermoplastic, crystalline or non-crystalline, reinforced or non-reinforced, etc.) have different polymer structural forms and rheological properties. All the factors affecting the above "field" will definitely affect the physical and mechanical properties, size, shape, precision and appearance of plastic products. In this way, the intrinsic link between process factors and polymer properties, structural form and plastic products will be expressed through plastic products. Injection molding often uses high pressure or ultra-high pressure injection, high speed injection to obtain a small molding shrinkage.

Send Inquiry